Z14AK BIOS Release Note:.

Z14AK BIOS R1.05 and EC R0.00.13:
1. Fix Serial port(485mode) fail whem resume from S3).
2. Fix LTE disappear in Win10 when RF Signal Slide Switch)為OFF and boot to win10

Z14AK BIOS R1.04 and EC R0.00.12:
1. fix new panel blinking(PWM Freq=200Hz->300HZ)

Z14AK BIOS R1.03 and EC R0.00.12:
1. fix "Win7 cannot switch to display port"
2. fix "Win7 cannot use RF switch"

Z14AK BIOS R1.02 and EC R0.00.12:
1. Change Panel brightness settings
2. Add inf update firmware function

Z14AK BIOS R1.01 and EC R0.00.12:
1. Fix LAN I210 some can not work (change aspm disable)

Z14AK BIOS RC.02 and EC R0.00.12:
1. Add USB LAN PXE function
2. Change VGA BIOS for new panel
3. Change PCIE9 type M2 to UNKOWN

Z14AK BIOS RC.02 and EC R0.00.12:
1. Add Intel AMT enable/disable in CPU configurations of setup menu
2. modify VBIOS for new panel(PS T8 =50, PWM on = 2000)
3. LTE disable, EC will power off it.

Z14AK BIOS RC.01 and EC R0.00.11:
1. Fix S3 LAN wakeup by battery mode
2. fix GPS can not be disabled in setup menu

Z14AK BIOS RC.00 and EC R0.00.10:
EC:
1. Fixed RF device status issue.
2. Fixed delay SYS_ON power OFF timer issue(BAT only).

Z14AK BIOS RB.06 and EC R0.00.08:
1.Set legacy USB function to auto
2.VGA DP port iboost level 7
EC:
1. Fixed HDD Heater issue.

Z14AK BIOS RB.05 and EC R0.00.07:
1.Set TCCActivationOffset = 20
2.Set I210 IO reserve = 20k for PCMCIA card fail with MXM card
3.Change Product name "Z14"

Z14AK BIOS RB.04 and EC R0.00.07:
# need to update ME
1. Fix Bluetooth enable/disable fail issue
2. fix USB power share on and DC plug in cannot be set independently.
3. Disable Sendor Hub
4. Add ME lock
5. Change String expansion card - PCMCIA/Expresscard


Z14AK BIOS RB.03 and EC R0.00.06:
1.Fix "Fn+F3 no sleep function"
2.Set VGA BIOS iboost mode enable and level=3

Z14AK BIOS RB.02 and EC R0.00.06:
1.Set Platform PL1-Pl4 disable, TDP PL1 enable value=0
2.Modify Battery calbration, don't show charging current,voltage and modify battery temp (C) from(K)

Z14AK BIOS RB.01 and EC R0.00.05:
1.Modify VGA BIOS for Panel blinking
2.New card can not work
3.Modify 2nd LAN aspm from auto to L0S

Z14AK BIOS RB.00 and EC R0.00.05:
1.Set primary display to SG mode from auto mode(for MXM).
2.Fix "Win10 can not find MXM card" issue.
3.Disable PLL3 ND PLL4.
4.Set TCCActivationOffset = 5 (for thermal sensor)
5.Modify Brightness level values
6.Modify system cannot found HDD without some Hdd heater connecter
7.Disable show advance and chipset under setup menu.

Z14AK BIOS RA.06 and EC R0.00.04:
1.No detect High brightness panel, GPIO set to output high 
2.Add RFID enable/disable for spec.
3.Modify setup menu string.

Z14AK BIOS RA.05 and EC R0.00.04:
1.Add CPU PL1 , PL2, PL3 and PL4 settings
2.Fix Battery 2 plug-in and not change the status under windows

Z14AK BIOS RA.04 and EC R0.00.04:
1.Add MXM CLK_REQ0
2.disable MXM aspm
3.The main page of Setup menu, Serial number and UUID will not reset without CMOS battery.
4.Wake-up from LAN default disable.
5.Add software “ME switch” under EC

Z14AK BIOS RA.03 and EC R0.00.03:
1.Switch string of “ Antenna GPS switch” and “ Antenna WWAN switch”
2.Add MXM function
3.modify HDD heater function for S4/S5 when power and  temporary <5 
4.Serial port 2 to RS232 mode is workable
5.2nd battery Calibration is ok
6.Add touch screen mode option
7.Add USBC to USB_OC1
8.Add Zero power ODD

Z14AK BIOS RA.02 and EC R0.00.03:
1.SLPDC enable
2.Fix PCMCIA port fail issue.
3.Assign GLAN2 CLK request =5
4.WLAN CLk request= 3
5.Device manager have yellow mark in USB device
6.Add Keyboard backlight timer


Z14AK BIOS RA.01 and EC R0.00.01:
1.Assign clock request = GLAN, CB Card54 and Wlan.
2.Update ME and BIOS 2 tparts for enable ISH
3.SetODD en:_GPP_ B_15  output low
4.Set Serial mode 1 GPP_A21,A22,A23 Output pin
5.Set Serial mode 2 GPP_G00,G01,G02 Output pin
6.Enable HDMI audio function
7.Enable COM3 port in SIO
8.Enable HDD



